SADDLES AND COMPONENTS

Saddle of rope lashing for poles (RM1846-W) is a simple and practical tool, it has six ring where the ropes can be tied, avoid undue embarrassment of them.

It has chain tensioner (RM1848-W) with a length of 915 mm for coupling to the pole with steering wheel to make the final adjustment. Made of heat treated aluminum alloy to meet the demands of work load and lightness in handling. 

The models of saddle for poles,  FLV4740-3W; FLV4740-4W; FLV4740-5W; FLV4740-9W; FLV4740-10W; FLV4740-15W; FLV4740-16W; FLV4740-17W; FLV4740-18W; FLV4740-19W; FLV4740-20W,  are manufactured in according to standard IEC-61236.

This tool is used as a coupling point for poles, blocks, or masts, allowing the hot poles to move away from the utility pole.

Available models include: saddles with clamp; with extension and clamp; 
with shackle and with extension and shackle.

Base made of heat treated aluminum alloy and stainless steel chain coupling to meet the demands of work load and lightness in handling, shackle and saddle coupling made of cast bronze. It has chain strecher (FLV00049-3) with length of 915 mm for coupling to the pole with steering wheel to make the final adjustment. 

The model of Crossarm type saddle (RM4744) useful for reduced workspace or already mounted with one or more pole saddles. The shackle installed on the saddle body, in turn, provides freedom of movement and allows the wire tong to move freely in either direction. It can be used on 76 x 108 mm and 102 x 203 mm. 

Simple saddle pole (RM4760-W) and double lift saddle (RM4760-1W), intended for coupling point connection of stick, rope blocks or masts for spacing from poles in "H" type frameworks or whenever the working clearance is too limited. 

Made with base and shoe of heat treated aluminum alloy to meet the demands of work load and lightness in handling, support strap and chain coupling made of steel, and saddle strap made of cast bronze. It has chain tensioner (RM1848-W) for coupling to the pole with steering wheel to make the final adjustment. It is equipped with strap and pin for connection of the rope block and wire tong respectively, allowing the free movement of both.  

The single lift saddle (RC400-1016), belonging to the group of conductor support equipment. Made of RITZGLAS® This saddle is equipped with a handle and pin to connect the block and wire tong, respectively, allowing free movement of both.

Used when the work space on the pole is limited, provides a total conductor lift of up to 915 mm. With the same load capacity as the aluminum lift saddles, but normally used in higher voltage systems where more room is needed to lift the conductors.

* For each wire tong.

The saddle extension  (RC400-0073) provide additional spacing between the sticks and the post, fixed to each other through the saddle. It has at one end preparation for coupling in the saddles through tear with appropriate geometry for fitting and drilling for installation of locking screw. At its other end, have a hole for fastening the pole clamp. Tool made of cast aluminum alloy with heat treatment so that the resistance is compatible with the efforts of its application.

The chain wheel tightener (RM1848-W) is a component of different models of sadlles, it´s responsible fastening the sadlle to the pole and the final adjustment is possible by using the tightening wheel. The chain wheel tightener provides easy installation of the sadlles, preventing it from sliding down or moving excessively, keeping it firm to its location. Haft manufactured in aluminum alloy, fork in micro-casting steel, stainless steel tightening wheel, welded link chain and safety pin.

The length of the chain stretcher can be increased by using the chain extension (RM1847, RM1847-3, RM1847-4; RM1847-6) for poles with larger diameters. Coupling made of heat treated aluminum alloy, attached to a chain made of steel and anticorrosive surface treatment. It has a safety pin also made of steel and with anti-corrosion treatment, which allows chain locking by the saddle. 

The concrete pole saddle screw (RM4740) is simple and practical to install, this tool is inserted into one of the holes in the pole and fastened with a wing nut. Tool belonging to the wire tong saddles and components assembly. Constructed of galvanized steel, coupling and steel butterfly nut, it has a total length of 295 mm. 

Wire tong saddle clevis (RM4740-14) is used to attach the wire tong butt-ring to a wire tong saddle, when used as an arm for the dual auxiliary arm, allowing the wire tong to rotate for attachment to the stirrup of the dual auxiliary arm. The piece structure consists primarily of a heat-treated aluminum alloy head, bronze alloy eye-screw, galvanized screws and lock washers, and a nylon-coated stainless-steel cable.

The Pole Clapms (RM4741-1; RM4741-2; RM4741-3 ; RM4741-5) are versatile and of great use, either in the distribution or transmission works, as they allow the fixing of rods in arrangements with other tools previously installed in the structure. 

Constructed of cast aluminum, the pole clamp and microfused butterfly nut tightening to the tubes, plus a spring-loaded locking device that prevents spontaneous opening of the collar, providing firmness and safety.

It has a smooth stainless steel internal coating to provide necessary adhesion without damaging the insulated tube. 

The adapter (RM4760-2), which converts a single saddle and single lift saddle into a double lift saddle for the mounting of two poles.